Key takeaways
- Find the best CPU thermal pads for gaming PCs, from soft gap fillers to phase-change sheets, with sizes, thickness, and conductivity explained.
date: 2026-11-19
category: “Buying Guides”
The best CPU thermal pads for gaming PCs are the ARCTIC TP-3 for soft gap filling, the Thermalright Extreme Odyssey II for high-conductivity silicone, the Thermal Grizzly PhaseSheet PTM for a clean phase-change sheet on a processor, the Innovation Cooling Graphite Thermal Pad for a reusable graphite sheet, and the OwlTree 3-Pack for a budget-friendly set of three thicknesses. Each suits a different job, because a pad that works well on graphics card memory is not always right for a processor, and a pad that fills a large, uneven gap is not always right for a thin, flat contact.
Thermal pads fill the space between a hot component and a heatsink. In a gaming PC, that space matters on the processor, on graphics card memory and power stages, on motherboard voltage regulators, and on storage drives under a heatsink. Thermal paste is still the usual choice directly between a processor and its cooler, because paste can form a very thin layer. Pads are the practical choice where the gap is larger, where surfaces are uneven, or where a clean, pre-cut sheet is easier to place.
Thickness comes first. A pad that is too thin leaves an air gap, and air is a poor conductor of heat. A pad that is too thick can prevent a heatsink from seating fully. Measure the gap before buying and match the pad to that gap. When the exact gap is not known, a soft pad that can compress a little, or a set with several thicknesses, gives more room for error. Never stack pads unless the manufacturer states that stacking is acceptable.
Softness is next. A very soft pad can mould itself around small height differences between neighbouring chips, which is common on graphics cards. A firmer pad holds its shape better and can be easier to cut and place. Most silicone pads are electrically insulating, so they can sit close to small components. Graphite pads are different: graphite conducts electricity, so a graphite sheet must stay on the intended surface and must not touch exposed pins or traces.
Table of Contents
- How to Choose a Thermal Pad for a Gaming PC
- ARCTIC TP-3 Premium Performance Thermal Pad
- Thermalright Extreme Odyssey II Thermal Pad
- Thermal Grizzly PhaseSheet PTM
- Innovation Cooling Graphite Thermal Pad
- OwlTree 3-Pack Thermal Pad
- Which Thermal Pad Fits Which Gaming PC Job
- Frequently Asked Questions
- Conclusion
How to Choose a Thermal Pad for a Gaming PC
Start with the component. For a processor heat spreader, a thin, flat sheet is usually right, and a phase-change or graphite sheet is designed for that flat contact. For graphics card memory, a silicone pad in a strip or sheet is usually right, because memory chips sit in a row and the gap to the cooler can vary. For motherboard voltage regulators and storage drives, a soft pad that can fill an uneven gap is often the most practical choice.
Next, confirm the thickness. Remove the old pad when possible and measure it with calipers, or measure the gap between the component and the heatsink. If the old pad has compressed over time, allow for that and choose a pad close to the original uncompressed thickness.
Then check the temperature range and handling. Most silicone pads in this guide are rated for continuous use to at least 150 degrees Celsius, which covers normal gaming use. A very soft pad can be harder to place neatly, while a firmer pad, a graphite sheet, or a phase-change sheet holds its shape better. A phase-change sheet needs enough mounting pressure to spread correctly once it warms up.
ARCTIC TP-3 Premium Performance Thermal Pad
The ARCTIC TP-3 is a soft, silicone-based thermal pad designed as a gap filler for uneven surfaces. Its very low hardness allows it to compress and mould around small height differences between closely spaced chips, which makes it a natural choice for graphics card memory, voltage regulators, and other components where the gap is not perfectly uniform. The version listed here is a pack of four strips, each 120 mm long and 20 mm wide, with a thickness of 1.0 mm, which suits long rows of memory chips.
ARCTIC describes the TP-3 as particularly soft, heat-conducting, vibration-damping, mouldable, and electrically insulating. The published hardness is 55 Shore OO, and the continuous use temperature is from minus 40 to 150 degrees Celsius. The pad can be stacked to 2.0 mm without performance loss, according to the product description. Note that ARCTIC does not publish a single thermal conductivity figure for the TP-3, so it should be judged on softness and intended use rather than a retailer number.
Specs
| Specification | Detail |
|---|---|
| Brand | ARCTIC |
| Size | 120 x 20 mm |
| Thickness | 1.0 mm |
| Pieces | 4 strips |
| Stackable | To 2.0 mm, as stated by the manufacturer |
| Hardness | 55 Shore OO |
| Temperature | Minus 40 to 150 degrees Celsius |
| Electrical behaviour | Electrically insulating |
| ASIN | B09V52D1N1 |
| Group | Mid-range |
Thermalright Extreme Odyssey II Thermal Pad
The Thermalright Extreme Odyssey II is a high-conductivity silicone thermal pad for gaming PCs, graphics cards, laptops, and other electronics where a firm, non-conductive pad is needed. The version listed here measures 85 mm by 45 mm, with a thickness of 1.0 mm. That size covers a useful area for memory chips and power stages without the waste of a very large sheet, and it can be cut to fit smaller components.
The Amazon product description states a thermal conductivity of 14.8 watts per metre-kelvin, and the series is described as the successor to the earlier Extreme Odyssey series. The pad is non-conductive, with a published breakdown voltage of 9.8 kilovolts. Thermalright lists the Extreme Odyssey II in sizes of 85 by 45 mm and 120 by 120 mm, with the smaller size available in thicknesses from 0.5 mm to 4 mm.
Specs
| Specification | Detail |
|---|---|
| Brand | Thermalright |
| Size | 85 x 45 mm |
| Thickness | 1.0 mm |
| Thermal conductivity | 14.8 watts per metre-kelvin, as stated in the product description |
| Electrical behaviour | Non-conductive |
| Breakdown voltage | 9.8 kilovolts |
| Other sizes | 85 x 45 mm and 120 x 120 mm |
| ASIN | B0CQ53GSBP |
| Group | Premium |
Thermal Grizzly PhaseSheet PTM
The Thermal Grizzly PhaseSheet PTM is a phase-change thermal sheet for processors and graphics chips. At room temperature it is a solid sheet that can be handled and placed easily. Once the system warms up, the material begins to liquefy above 45 degrees Celsius, and it then behaves more like a thermal paste, spreading into a very thin layer. That change is the point of the design: the sheet is easy to place when cold, and it forms a close contact when hot.
The sheet listed here measures 50 mm by 40 mm, with a thickness of 0.2 mm, which covers a processor heat spreader and can also be used on a graphics chip. The operating temperature range is from minus 75 to 150 degrees Celsius, and the material is electrically non-conductive. Thermal Grizzly states that a contact pressure of around 300 to 400 newtons is required for optimum distribution, and that the sheet reaches its maximum thermal conductivity after around ten thermal cycles above 60 degrees Celsius. It is not a gap filler, so it should not be used where a large gap needs to be bridged.
Specs
| Specification | Detail |
|---|---|
| Brand | Thermal Grizzly |
| Size | 50 x 40 mm |
| Thickness | 0.2 mm |
| Material | Phase-change material |
| Phase change begins | Above 45 degrees Celsius |
| Temperature | Minus 75 to 150 degrees Celsius |
| Electrical behaviour | Non-conductive |
| Mounting pressure | Around 300 to 400 newtons, as stated by the manufacturer |
| ASIN | B0DB84CQW6 |
| Group | Premium |
Innovation Cooling Graphite Thermal Pad
The Innovation Cooling Graphite Thermal Pad is a reusable graphite sheet designed as a permanent alternative to thermal paste for processors, graphics cards, and game consoles. The version listed here measures 40 mm by 40 mm, which suits a processor heat spreader. The pad is flexible and compressible to some extent, so it can form a close contact with the heat spreader and the cooler, and it does not dry out in the way that some pastes can over time.
The published thermal conductivity is 35 watts per metre-kelvin, and the published operating temperature range is from minus 200 to 400 degrees Celsius. The pad is designed to be reused, which can suit a gaming PC that is opened regularly, provided it is kept clean and undamaged. The important warning is that graphite conducts electricity, so the sheet must stay on the intended surface and must not touch exposed pins, traces, or neighbouring components.
Specs
| Specification | Detail |
|---|---|
| Brand | Innovation Cooling |
| Size | 40 x 40 mm |
| Material | Graphite |
| Thermal conductivity | 35 watts per metre-kelvin |
| Temperature | Minus 200 to 400 degrees Celsius |
| Electrical behaviour | Electrically conductive, so placement must avoid exposed contacts |
| Reusable | Yes, designed as a permanent alternative to thermal paste |
| ASIN | B07CK9SHZG |
| Group | Mid-range |
OwlTree 3-Pack Thermal Pad
The OwlTree 3-Pack is a budget-friendly set of silicone thermal pads for gaming PCs, laptops, graphics cards, and storage drives. The pack includes three sheets, each 100 mm by 100 mm, in thicknesses of 0.5 mm, 1.0 mm, and 1.5 mm. That combination allows the correct thickness to be selected during the build, instead of guessed before ordering.
The published thermal conductivity is 12.8 watts per metre-kelvin, which is a high figure for a pad in the budget group. The material is described as thermal silica gel, and the pads are heat resistant and cuttable. The three thicknesses cover the most common gaps in a gaming PC, from a thin gap on a storage drive to a thicker gap on a graphics card.
Specs
| Specification | Detail |
|---|---|
| Brand | OwlTree |
| Size | 100 x 100 mm per sheet |
| Thicknesses | 0.5 mm, 1.0 mm, and 1.5 mm |
| Pieces | 3 sheets, one of each thickness |
| Thermal conductivity | 12.8 watts per metre-kelvin |
| Material | Silicone-based thermal gel |
| Cuttable | Yes |
| ASIN | B09DC772PR |
| Group | Budget |
Which Thermal Pad Fits Which Gaming PC Job
For graphics card memory, a silicone pad is usually the right starting point. The ARCTIC TP-3 suits uneven memory rows, because its soft material can compress around small height differences. The Thermalright Extreme Odyssey II suits a card where a firmer, high-conductivity pad is preferred and the gap is known. The OwlTree 3-Pack suits a card where the thickness is not certain.
For a processor heat spreader, a thin sheet is usually right. The Thermal Grizzly PhaseSheet PTM suits a processor with a close-fitting cooler and enough mounting pressure. The Innovation Cooling Graphite Thermal Pad suits a processor where a reusable sheet is preferred and the builder can place it accurately.
Frequently Asked Questions
What thickness of thermal pad should I use for a gaming PC?
Measure the gap between the component and the heatsink, or measure the old pad with calipers when it is removed. Match the new pad to that measurement, and allow for compression if the old pad has flattened over time. A set with several thicknesses allows the correct size to be selected during the build.
Can thermal pads replace thermal paste on a CPU?
Thermal pads can replace paste on a flat processor heat spreader when the pad is designed for that use, such as a phase-change sheet or a graphite sheet. A thick silicone gap filler is not the right choice for that thin contact, because it is designed to bridge a larger gap.
Are thermal pads electrically conductive?
Most silicone thermal pads are electrically insulating, which means they do not conduct electricity and can be used close to electronic components. Graphite pads are different, because graphite conducts electricity, so a graphite sheet must stay on the intended surface and must not touch exposed pins or traces.
How often should thermal pads in a gaming PC be replaced?
Silicone pads are generally replaced when a cooler or graphics card is opened, because they take a set and may not spring back fully. A graphite pad is designed to be reused, provided it is kept clean and undamaged. A phase-change sheet is generally replaced when it is removed.
Conclusion
The best CPU thermal pads for gaming PCs depend on the component, the gap, and the layout of the machine, not on a single conductivity figure. The ARCTIC TP-3 is the soft gap filler for uneven graphics card memory. The Thermalright Extreme Odyssey II is the high-conductivity silicone pad for a firm, insulating fit. The Thermal Grizzly PhaseSheet PTM is the clean phase-change sheet for a flat processor or graphics chip. The Innovation Cooling Graphite Thermal Pad is the reusable graphite sheet for a processor, with careful placement because it conducts electricity. The OwlTree 3-Pack is the budget-friendly set for several thicknesses. Measure the gap, check the published temperature range and electrical behaviour, and choose the pad that matches the job.
As an Amazon Associate, we earn from qualifying purchases.
|—|—|
Further reading