Updated Nov 19, 2026· 10 min read

Key takeaways

  • Find the best PC fan hubs for gaming PCs, from simple 10-port PWM hubs to software-controlled RGB hubs, and choose the right hub for your build and fans.

As an Amazon Associate, we earn from qualifying purchases.

The best PC fan hub for most gaming PCs is the Corsair iCUE Commander Core XT, because it controls six PWM fans and RGB lighting from one compact unit through software, with fan-stop operation at low load and temperature monitoring built in. If you want a simpler setup without software, the ARCTIC Case Fan Hub is the best budget choice, because it powers ten PWM fans from a single motherboard header and SATA power. For a large addressable RGB build, the Thermalright ARGB Fan Hub X8 is the best value option, with eight PWM ports and eight ARGB ports. NZXT owners should look at the NZXT RGB and Fan Controller for a standard build, or the newer NZXT Control Hub for NZXT single-frame fans.

A fan hub solves a common problem in gaming builds. A typical case now holds six, eight, or ten fans, while a typical motherboard offers only three to six fan headers. A hub takes one control signal from the motherboard, or from software through a USB header, and shares it across many fans, while drawing power through a SATA connector.

Table of Contents

  • What a PC Fan Hub Does
  • PWM, DC, and ARGB Explained
  • How to Choose a Fan Hub for a Gaming PC
  • The 5 Best PC Fan Hubs for Gaming PCs
  • How to Install a Fan Hub
  • Common Mistakes to Avoid
  • FAQ
  • Conclusion

What a PC Fan Hub Does

A PC fan hub is a small distribution board inside the case, usually mounted with magnets or adhesive tape. It connects to the power supply for power, to the motherboard for a control signal, and to each case fan for power and speed control. Some hubs also connect through an internal USB header so software can control fan curves and lighting.

The main benefit is capacity. Instead of using a separate motherboard header for every fan, a hub gives you a single central point for six to ten fans, which makes cable management easier and protects the motherboard, because the hub draws fan power from SATA power. In a basic PWM hub, every fan receives the same signal. In a software hub, each fan can have its own curve.

PWM, DC, and ARGB Explained

PWM stands for pulse width modulation, and it is the standard way modern motherboards control fan speed. A four-pin PWM fan receives a signal that tells it how fast to spin, and the motherboard changes that signal in response to temperature. Most gaming fans today are four-pin PWM fans, and every hub in this guide supports them. A three-pin DC fan is controlled by changing voltage instead.

ARGB stands for addressable RGB, and it uses a three-pin five-volt connector. Each LED can be addressed individually, so software can create waves and per-fan effects. Standard RGB uses a four-pin twelve-volt connector, and all LEDs on a strip show the same colour at once. The two systems are not interchangeable, and plugging a five-volt ARGB device into a twelve-volt RGB header can damage it. Several hubs here support ARGB only, so confirm which lighting connector your fans use.

How to Choose a Fan Hub for a Gaming PC

Begin by counting your fans, including every case fan and radiator fan, then add one or two spare ports for a future upgrade. A six-port hub suits a standard mid-tower, while a ten-port hub suits a large airflow case. A basic PWM hub is enough if all fans can follow one motherboard curve, while a software hub is better for different curves or fans that stop at idle.

Check compatibility carefully. Make sure the hub has enough PWM and ARGB ports, that your power supply has a free SATA connector, and that your motherboard has a free fan header and, for software hubs, a free internal USB header. A Corsair hub works best with Corsair RGB fans and iCUE software, an NZXT hub works best with NZXT fans and CAM software, and a standard ARGB hub works with any fan using the standard three-pin ARGB connector.

The 5 Best PC Fan Hubs for Gaming PCs

The five hubs below cover the main ways to control fans in a gaming PC, from a simple ten-port PWM hub to a full software controller. Each one is described from its published specifications.

1. Corsair iCUE Commander Core XT

The Corsair iCUE Commander Core XT is the most capable hub in this guide, and the best choice for a PC that already uses Corsair RGB fans. It controls up to six PWM fans and up to six Corsair RGB fans from one unit, with a second lighting channel for other Corsair RGB devices. It connects through an internal USB header and draws power from SATA. Through Corsair iCUE software, each fan channel can have its own speed curve, Zero RPM mode lets fans stop at low load, and two included temperature sensors let curves respond to air temperature inside the case. Lighting covers up to 264 LEDs.

Specs

Feature Specification
Brand Corsair
Fan channels 6 PWM fan channels
RGB channels 2 RGB channels, up to 264 LEDs
Fan control Per-fan curves through iCUE software, Zero RPM mode
Temperature sensors 2 included temperature sensors
Power SATA power connector
Connection Internal USB header
ASIN B09GHTMJMY

2. NZXT RGB and Fan Controller

The NZXT RGB and Fan Controller is a solid mid-range choice for a PC that uses NZXT RGB fans and NZXT CAM software. It provides six RGB lighting channels and three fan channels, so it can drive lighting across several fans and strips while controlling speed for the main case fans. It connects through an internal USB header and SATA power, and mounts with magnets inside the case. Each RGB channel supports up to 40 LEDs, with up to 120 LEDs in total, and CAM provides lighting presets and fan curves. With three fan channels, it suits a build with three main fan groups.

Specs

Feature Specification
Brand NZXT
Fan channels 3 fan channels
RGB channels 6 RGB lighting channels
LED capacity Up to 40 LEDs per channel, up to 120 LEDs in total
Fan control Fan curves and Zero RPM mode through NZXT CAM software
Power SATA power connector
Connection Internal USB header
Mounting Magnetic mounting
ASIN B0B3QY4LYQ

3. NZXT Control Hub

The NZXT Control Hub is the newer NZXT option here, designed around NZXT single-frame fans, which combine several fans into one frame with a single cable. It controls up to five PWM fans, or up to four NZXT single-frame fans, and manages RGB lighting through NZXT CAM software. It uses four NZXT eight-pin ports for single-frame fans, plus an NZXT RGB channel for other NZXT lighting devices. Each eight-pin channel supports up to 96 LEDs, and the RGB channel supports up to 40 LEDs. Power comes from a SATA connector, and control comes through an internal USB header.

Specs

Feature Specification
Brand NZXT
Fan channels Up to 5 PWM fans, or up to 4 NZXT single-frame fans
RGB ports 4 NZXT eight-pin ports and 1 NZXT RGB channel
LED capacity Up to 96 LEDs per eight-pin channel, up to 40 LEDs on the RGB channel
Fan control PWM fan speed control through NZXT CAM software
Power SATA power connector
Connection Internal USB header
ASIN

4. Thermalright ARGB Fan Hub X8

The Thermalright ARGB Fan Hub X8 is the best value ARGB hub in this guide, because it gives you eight PWM fan ports and eight ARGB ports in one compact unit, with no software to install and no brand lock-in. It works with any standard four-pin PWM fan and any standard three-pin five-volt ARGB fan or light strip, so it suits a mixed-brand build. It draws power from a SATA connector and takes its PWM and ARGB signals from the motherboard. Note that it supports five-volt three-pin ARGB only, and twelve-volt four-pin RGB devices are not supported.

Specs

Feature Specification
Brand Thermalright
Fan ports 8 PWM fan ports
ARGB ports 8 ARGB ports, 5V 3-pin
Lighting support ARGB motherboard sync, 12V 4-pin RGB not supported
Power SATA power connector
Control PWM signal and ARGB signal from the motherboard
Mounting Magnetic suction and adhesive pad
Dimensions 140 by 64 by 16 mm
ASIN B09SZBJ5JZ

5. ARCTIC Case Fan Hub

The ARCTIC Case Fan Hub is the simplest hub in this guide, and the best budget choice for a PC that needs many fans but no lighting control. It is a ten-fold PWM distributor with ten four-pin PWM outputs, so it can power and control up to ten PWM case fans from a single motherboard fan header. Power comes from a SATA connector, so the motherboard header supplies only the PWM control signal, not the power for ten fans. There is no software or lighting control, which keeps installation simple. The trade-off is that all fans share one speed signal.

Specs

Feature Specification
Brand ARCTIC
Fan ports 10 PWM fan ports
Fan connector 4-pin PWM
Lighting support No RGB or ARGB control
Power SATA power connector
Control Single PWM signal from one motherboard fan header
Compatibility PWM case fans
ASIN B0887VG14J

How to Install a Fan Hub

Mount the hub first, where fan cables can reach it without stretching. Connect a SATA power cable from the power supply into the hub. For a basic hub, run the PWM input cable to a chassis fan header rather than the CPU fan header. For a software hub, also connect the internal USB cable to a free USB header. Connect the fans one at a time, and connect ARGB cables to the ARGB ports if the hub supports lighting. Keep cables tidy, then switch on and set a fan curve.

Common Mistakes to Avoid

The most common mistake is mixing five-volt ARGB and twelve-volt RGB connectors. They look similar, but they use different voltages and pin counts, and they are not interchangeable, so check the voltage and pin count before connecting anything. Another mistake is connecting too many fans to a motherboard header without a powered hub, so use a SATA-powered hub for a large fan count. A third mistake is forgetting the USB header, because software hubs need a free internal USB header.

FAQ

How many fans can a PC fan hub control?

A fan hub can control as many fans as it has ports, provided it has its own power input. The hubs here range from three fan channels on the NZXT RGB and Fan Controller to ten PWM ports on the ARCTIC Case Fan Hub, with six ports on the Corsair hub and eight on the Thermalright hub. A SATA-powered hub is safer for six or more fans.

Do I need a fan hub if my motherboard has enough fan headers?

You do not need a hub if your motherboard has a free header for every fan, but a hub can still help. It centralises cables, makes future upgrades easier, and lets software hubs set per-fan curves and lighting effects. If you have more fans than headers, or you want coordinated RGB lighting, a hub is the practical solution.

Can a fan hub control RGB lighting and fan speed at the same time?

Yes, many hubs control both, but in different ways. A standard ARGB hub such as the Thermalright model passes the PWM and ARGB signals from the motherboard to all connected fans. A software hub such as the Corsair or NZXT hub uses its own application to set fan curves and lighting effects. A basic PWM hub such as the ARCTIC model controls fan speed only.

What is the difference between a fan hub and a fan splitter?

A fan splitter shares one motherboard header between two or three fans without adding power, so all fans on the splitter share the same signal and draw power from that header. A fan hub adds its own SATA power input, so it can support many more fans safely, and it often adds more ports, lighting control, or software control. Use a splitter for one or two extra fans, and use a hub when you need many fans or ARGB lighting.

Conclusion

The best PC fan hub depends on how many fans you have, whether you want software control, and which lighting system your fans use. The Corsair iCUE Commander Core XT is the best overall choice for a Corsair RGB build, with six independent PWM channels, two RGB channels, temperature sensors, and fan-stop operation. The NZXT RGB and Fan Controller is a good mid-range choice for NZXT builds, while the NZXT Control Hub is better for NZXT single-frame fans. The Thermalright ARGB Fan Hub X8 is the best value choice for a standard ARGB build, and the ARCTIC Case Fan Hub is the best budget choice for a simple ten-fan PWM setup. Before you buy, count your fans, check your connectors, and confirm a free SATA connector and, for software hubs, a free USB header.

|—|—|

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.