Key takeaways
- Find the best PC fan grills for 120mm and 140mm fans. Compare wire, mesh and finger guards for airflow, safety, fit and easy installation for your build.
The best PC fan grills are the Noctua fan grill for 120mm fans, the ARCTIC fan grill in 120mm and 140mm sizes, the Nivithi 120mm grill guard in a two-pack, and the Honbay 120mm guard in a four-pack. Each one sits over a case fan and blocks fingers, cables, and loose objects from touching spinning blades, while leaving most of the airflow path open. If you want one simple answer, start with a nickel-plated steel wire grill in the exact size of your fan, then choose a multi-pack when you need to cover several fans in the same build.
As an Amazon Associate, we earn from qualifying purchases.
A fan grill is a small accessory with a clear job. It does not cool the PC by itself, and it does not replace a case fan. It protects the fan, the cables near it, and anyone who reaches into an open case. It also helps stop a stray cable from dropping into a blade, which can stall a fan or damage a cable. For builders with children or pets nearby, and for open or test-bench builds where fans are exposed, that protection matters more than it does in a closed case with a solid side panel.
Table of Contents
- How to Choose a PC Fan Grill
- Noctua Fan Grill for 120mm Fans, Set of 2
- ARCTIC Fan Grill 120mm
- ARCTIC Fan Grill 140mm
- Nivithi 120mm PC Fan Grill Guard, 2-Pack
- Honbay 120mm Computer Case Fan Guards, 4-Pack
- Frequently Asked Questions
- Conclusion
How to Choose a PC Fan Grill
Start with size. A grill must match the fan it covers, not the size of the hole in the case. A 120mm fan needs a 120mm grill, and a 140mm fan needs a 140mm grill. Check the fan frame or the fan label for the size before ordering. A grill that is too small will not cover the blades, and a grill that is too large will not line up with the mounting holes.
Next, look at material and wire spacing. Most PC fan grills use steel wire in a concentric ring pattern, with radial supports that hold the rings in place. Nickel-plated steel is a common choice because it resists corrosion and keeps its shape. Wide spacing lets more air through, while closer spacing gives more protection against small objects. For a standard case fan, a wire grill with open spacing is a good balance.
Mounting is the third point to check. Many wire grills use the same four corner screws as the fan, so they can be fitted between the fan and the case, or on the outer face of the fan. Some use a hook-on design that clips onto the fan frame. Others include push-pin mounts that hold the grill a short distance away from the blades. That gap can reduce turbulence, which helps keep airflow smooth and noise low. Make sure the grill sits flat and does not touch the blades, and spin the fan by hand, with the power off, after fitting it.
Airflow impact should not be overstated. A well-designed wire grill is largely open, so the published airflow impact for several models in this guide is less than one percent. A grill with a dense mesh or a fine screen will block more air and collect more dust. If maximum airflow is the priority, choose a simple wire grill rather than a mesh cover. Also think about pack size: a single grill suits one exposed fan, a two-pack suits an intake and exhaust pair, and a four-pack suits a full case. Finally, check clearance, because a grill adds a small amount of depth that can matter behind a tight side panel.
Noctua Fan Grill for 120mm Fans, Set of 2
The Noctua fan grill for 120mm fans is the premium pick in this guide. It is sold as a set of two black grills for 120mm fans, and it is designed for builders who want strong protection with careful attention to airflow and noise. The grill uses an offset design with rounded struts, which is intended to reduce turbulence as air passes through the grill.
Installation is flexible. The set includes standard fan screws and a tool-free push-pin mounting system, with one set of screws and one set of push-pins for each grill. The push-pin system can be fitted even when the fan is already installed in a PC. It also introduces an additional five-millimetre offset between the grill and the fan. Without the extra spacing, the manufacturer reports an average airflow impact of around three percent across its fan models, with an average noise increase of around one point two decibels. With the offset mount, those figures fall to around two percent and around zero point six decibels. Those figures come from the manufacturer’s own fan models, so results with other fans may differ.
The set is a good match for a 120mm rear exhaust fan, a 120mm intake fan behind an open front panel, or a 120mm fan on a radiator where fingers and cables are close to the blades. The black finish suits a dark build, and the two-pack covers a common pair of fans. The six-year manufacturer warranty listed for this product also signals that it is built as a long-term accessory.
Specs
| Feature | Detail |
|---|---|
| Fan size | 120mm |
| Pack size | Set of 2 |
| Colour | Black |
| Mounting | Screws and tool-free push-pin mounts included |
| Offset | Five-millimetre offset with push-pin mounting |
| Warranty | Six years |
| ASIN | B0B214M354 |
ARCTIC Fan Grill 120mm
The ARCTIC fan grill for 120mm fans is a simple nickel-plated steel wire grill, and it is the straightforward choice for a single 120mm fan. It is made from nickel-plated steel, which gives it a bright silver finish and a rigid feel for its size. The grill measures 105mm by 105mm across its wire area, while it is sized to fit a standard 120mm fan frame. That smaller wire area is normal for this type of grill, because the wire pattern sits inside the fan frame rather than covering the full outer edge.
The grill uses a hook-on mounting system, so it clips onto the fan rather than relying only on screws. The pack includes four mounting screws as well, which gives a second fitting option when a screw mount is more secure. The published airflow impact is less than one percent, which makes this grill a good choice when the goal is protection without a noticeable change in cooling.
Specs
| Feature | Detail |
|---|---|
| Fan size | 120mm |
| Grill size | 105mm by 105mm |
| Material | Nickel-plated steel |
| Colour | Silver |
| Mounting | Hook-on system, four mounting screws included |
| Airflow impact | Less than one percent |
| Pack size | Single grill |
| ASIN | B075S6HSW7 |
ARCTIC Fan Grill 140mm
The ARCTIC fan grill for 140mm fans follows the same design as the 120mm version, with a larger wire area to match a larger fan. It is also made from nickel-plated steel, and it uses the same hook-on mounting system. The grill measures 125mm by 125mm across its wire area, while it is sized for a standard 140mm fan. That size is important, because a 120mm grill will not cover a 140mm fan, and a 140mm fan moves air across a wider blade area that needs full protection.
The published airflow impact is again less than one percent, so this grill adds protection without a large penalty in airflow. The nickel-plated steel construction is rigid enough to keep its shape when fitted, and the silver finish suits a light or neutral case interior. The grill is a good match for a 140mm front intake fan, a 140mm top exhaust fan, or a 140mm fan on a large air cooler where the blades are exposed at the edge of the case.
Specs
| Feature | Detail |
|---|---|
| Fan size | 140mm |
| Grill size | 125mm by 125mm |
| Material | Nickel-plated steel |
| Colour | Silver |
| Mounting | Hook-on system |
| Airflow impact | Less than one percent |
| Pack size | Single grill |
| ASIN | B075S76H6G |
Nivithi 120mm PC Fan Grill Guard, 2-Pack
The Nivithi 120mm PC fan grill guard is a black metal guard sold as a two-pack, and it is the practical choice for a pair of 120mm fans. The guards measure 120mm by 120mm, which matches the outer size of a standard 120mm fan frame. The black powder-coated finish gives a dark, uniform look that blends into a black case, and the metal construction feels solid for a guard in the budget group.
Fitting is by screw mounting, using the same corner holes as the fan. The published specification lists screw mounting with included hardware, so the guards can be fitted on the outer face of a fan or between the fan and the case panel. The two-pack covers a common intake and exhaust pair, or two fans on the same side of a case. The guard is designed to prevent contact with the fan blades and to keep cables away from the spinning parts. Its full-cover design is more enclosed than a simple wire ring grill, which gives more protection where fingers or cables are close to the fan.
Specs
| Feature | Detail |
|---|---|
| Fan size | 120mm |
| Size | 120mm by 120mm |
| Material | Metal |
| Finish | Black powder-coated |
| Mounting | Screw mounting with included hardware |
| Pack size | 2-pack |
| Intended use | Case fan guard for 120mm cooling fans |
| ASIN | B0CYHB7J9H |
Honbay 120mm Computer Case Fan Guards, 4-Pack
The Honbay 120mm computer case fan guards are a four-pack of metal guards with screws, and they are the best choice in this guide for covering a full case of 120mm fans. Each guard measures 120mm by 120mm, which matches a standard 120mm fan frame. The pack includes four fan grill guards and mounting screws, so a builder can fit four fans without ordering extra hardware.
The design is simple and rugged, with a minimal pattern that focuses on protection rather than decoration. The guards fit standard 120mm square fans, and the screw fitting holds them flat against the fan frame. That flat fit matters in a full case, because a guard that sits unevenly can vibrate or rub against a nearby panel. This four-pack suits a gaming PC with several 120mm fans, a workstation with multiple intake and exhaust fans, or a builder who wants spares for a future case swap. It is in the budget group, and its value comes from the pack size rather than from a special mounting system or a decorative pattern.
Specs
| Feature | Detail |
|---|---|
| Fan size | 120mm |
| Size | 120mm by 120mm |
| Material | Metal |
| Mounting | Screws included |
| Pack size | 4-pack |
| Compatibility | Standard 120mm square fans |
| Design | Simple, rugged protective grill |
| ASIN | B09ZY5K8Z8 |
Frequently Asked Questions
What size PC fan grill do I need?
Match the grill to the fan size, not to the case opening. A 120mm fan needs a 120mm grill, and a 140mm fan needs a 140mm grill. Check the fan label or the fan frame for the size, and check the grill listing for the same number. A grill that is too small leaves part of the blade area exposed, and a grill that is too large will not line up with the mounting holes.
Do PC fan grills reduce airflow?
A wire grill reduces airflow by a small amount, because the wire itself sits in the air path. For the nickel-plated steel grills in this guide, the published impact is less than one percent, which is small enough that most builders will not notice a change in cooling. A grill with a dense mesh or a fine screen blocks more air than a wire grill, so choose a wire grill when airflow is the priority.
How do I install a PC fan grill?
Most grills fit with the same four corner screws as the fan. Place the grill on the outer face of the fan, line up the holes, and tighten the screws evenly so the grill sits flat. Some grills use a hook-on clip or a push-pin mount instead, which can be fitted without removing the fan. After fitting, turn the fan by hand with the power off and check that the blades do not touch the grill.
What is the difference between a fan grill and a fan filter?
A fan grill is a protective guard that blocks fingers, cables, and large objects from touching spinning blades. A fan filter is a fine mesh or foam layer that catches dust before it enters the case. A grill is open and has little effect on airflow, while a filter is denser and needs regular cleaning to keep airflow steady. The five products in this guide are grills, not filters.
Conclusion
The best PC fan grill depends on how many fans you need to cover and how much you want to spend. The Noctua set of two is the premium choice for a 120mm fan where airflow, noise, and a tool-free offset mount matter. The ARCTIC 120mm and 140mm grills are the straightforward nickel-plated steel choices for a single fan in each size, with a published airflow impact of less than one percent. The Nivithi two-pack is the practical choice for a pair of 120mm fans in a black case, and the Honbay four-pack is the practical choice for a full case of 120mm fans.
|—|—|
Further reading
- Best PC Fan Filters to Keep Your Build Clean and Cool
- Best SATA Cables for SSDs, HDDs, and Clean PC Builds
- Best RGB Controllers for a Brighter, Smarter PC Build
- Best PC Fan Hubs for Gaming PCs: Top 5 Picks for 2026
- Best USB Ethernet Adapters for Fast Wired Internet
- Best WiFi Antennas for PC: Stronger Signal in 2026